Eachine Wizard TS130 Racing Drone PNP Omnibus F4 OSD 20A Dshot600 40CH Smart Audio 200mW VTX 

Item Specification
Eachine Wizard TS130
Wheelbase: 130mm
Material: 3K carbon fiber
Top plate thickness: 2mm
Bottom plate thickness: 3mm
Artist: hydrographics transfer printing
TS 20A 4in1  
Continuous current: 20A
Peak current (5S): 25A
Input voltage: 2-4S
Supports Dshot600, Dshot300, Dshot150
Size: 27x27mm
Weigjt: 3.3g
TS1507 4100KV Brushless Motor
Idle Current (Io/10V): 1.68A
Lipo Cell: 3-4S
Weight: 17.6g
Max Continuous Current: 26A
Max Continuous : 416W
Max thrust: 626g(4S/3″)
Configu-ration: 9N/12P
Motor Resistance (RM): 0.0495 Ω
Stator Diameter: 15mm
Stator Thickness: 7mm
Motor Diameter: 21.6mm
Motor Body Length: 15.5mm
Overall Shaft Length: 29mm
Prop adapter shaft: M5
Bolt holes spacing: 12mm
Bolt thread: M2
Propeller: 3”
Customized Omnibus F4
CPU: f4STM32 F405 SCM
Input voltage: 3-4S
Sensor: MPU6000 SPI
Built in OSD
Built in 5V 2A BEC
Size: 25x25mm
Weight: 2.3g
5.8G 40CH 25mw / 100mw / 200mw VTX
Input voltage: 7-24V
Dimensions: 20x20mm
Size: 27mm×27mm×4.5mm
Adjustable 25mw / 100mw / 200mw
Supports smart audio (remote OSD parameter adjustment)
Solution: 1/3” Sony SUPER HAD II CCD+Nextchip 2040 DSP
Pixel:PAL: 976(H) x 494(V);NTSC: 768(H)×494(V)
TV System: PAL/NTSC (based on country)
Resolution: 600TVL(color)  650TVL(B&W)
Synchronization: internal
Min. Illumination: 0.01Lux
WDR: support
OSD programming board: support
White Dot Repair: support
Camera Title: support
Image Adjustment: support
OSD: Edit Name, Power, Flying time
Input Power: 5-40V
Storage Temperature: -40 C ~ 60 C
Working Temperature: -10 C ~ 50 C
Power Consumption: 70mA
Low voltage alarm: Support
Size: 18.5*19mm (bracket excluded)
Weight: 5.3g (bracket excluded)
Recommend battery: 3-4S 550-850mah

XMM-VTX Description:
The XMM-VTX operates with a single button. There are three LED indicators (red light indicates CH1-8; blue light indicates BAND1-5; green light indicates power 1-3 files <25-100-200mW>), and TBS SmartAudio remote control is supported.
Long press button 3S (3 LED indicators are all bright) release into CH switching operation, and the red light will flash, flash 1 time means that the current is CH1 (red light flashes 2-8 times respectively represent CH2-CH8) At this time, press the button CH for 1 and the red light will flash correspondingly. CH1-8 cycle. Press and hold the button 3S again (3 LED indicators are all on) to enter the BAND switching operation, and the blue light will flash, flashing once indicates that the current is BAND1 (the blue light flashes 2-5 times to represent BAND2-BAND5 respectively). Short press the button BAND plus 1, the blue light will flash the corresponding number of times. BAND1-5 loop. Press and hold button 3S again (3 LED indicators are all on) to enter the power switching operation, and the green light will flash, flashing once represents the current 1st power (green flash 2-3 times respectively represent 2-3 power) At this time, press the button power and add 1 file, the green light will flash correspondingly. Power file 1-3 cycles. Press and hold button 3S again (3 LEDs are all on) to release the above settings. Note that the previous settings will not save the settings if the power is turned off before saving. For example, if only the CH is set, it is necessary to press and hold the 3S operation three times to save.
Press and hold button 8S (green light) to exit PIT mode.
Package Included:
1 x Eachine Wizard TS130 frame kit
1 x TS 20A 4in1 Brushless ESC
4 x TS1507 4100KV brushless motor
1 x F4 controller
1 x FOXEER Arrow MICRO PRO camera
1 x 5.8G 40CH 25mw 100mw 200mw switchable VTX
2 x T3056C 3-blade propeller transparent white CW
2 x T3056C 3-blade propeller transparent white CCW
2 x T3056C 3-blade propeller blue CW
2 x T3056C 3-blade propeller blue CCW
1 x
1 x Battery strap
2 x Carbon fiber wrench
10 x Nylon tie


Leave a Reply

Your email address will not be published. Required fields are marked *